Difference between revisions of "Geeetech M1 3D printer"
(→Printer Introduction) |
|||
Line 2: | Line 2: | ||
Geeetech Mozi is a very good 3D printer on the market. | Geeetech Mozi is a very good 3D printer on the market. | ||
+ | |||
+ | 1 Printer Introduction | ||
+ | |||
+ | 2 Printer Maintenance | ||
+ | |||
+ | 2.1 How to Clean the Nozzle | ||
+ | |||
+ | |||
+ | 2.2 How to Replace the Hot End | ||
+ | |||
+ | |||
+ | 2.3 How to Replace the Screen | ||
+ | |||
+ | |||
+ | 2.4 How to Replace the Control Board | ||
+ | |||
+ | |||
+ | 2.5 How to Automatically Level | ||
+ | |||
+ | |||
+ | 2.8 How to Manually Level | ||
+ | |||
+ | |||
+ | 3 Troubleshooting | ||
+ | |||
+ | |||
+ | 3.1 Black Screen | ||
+ | |||
+ | |||
+ | 3.2 Update Firmware | ||
+ | |||
+ | |||
+ | 3.3 Minimum Temperature Error | ||
+ | |||
+ | |||
+ | 3.4 Automatic Leveling Failed | ||
+ | |||
+ | |||
+ | 3.5 How to Import Profiles into Cura | ||
+ | |||
+ | |||
+ | 3.6 Filament Does Not Stick to the Hot Bed | ||
+ | |||
+ | |||
+ | 3.7 Uneven Thickness of the First Layer of Print | ||
+ | |||
+ | |||
+ | 3.8 Prints Are Brushed or Missed | ||
+ | |||
+ | |||
+ | 3.9 Under-Extrusion and Over-Extrusion | ||
+ | |||
+ | |||
+ | 3.10 Insufficient Sealing of the Top Layer | ||
+ | |||
+ | |||
+ | 3.11 Printing Offset | ||
+ | |||
+ | |||
+ | 3.12 Surface Spots and Stripes | ||
+ | |||
+ | |||
+ | 3.13 Gaps Between Edges and Infill | ||
+ | |||
+ | |||
+ | 3.14 Rough Corners | ||
+ | |||
+ | |||
+ | 3.15 Top Surface Scratches | ||
+ | |||
+ | |||
+ | 3.16 Holes at the Bottom of the Corner | ||
+ | |||
+ | |||
+ | 3.17 Uneven Sides | ||
+ | |||
+ | |||
+ | 3.18 How to print TPU | ||
+ | |||
+ | |||
+ | 3.19 How to print ABS | ||
+ | |||
+ | |||
+ | 3.20 How to print PETG |
Revision as of 08:49, 24 October 2024
Printer Introduction
Geeetech Mozi is a very good 3D printer on the market.
1 Printer Introduction
2 Printer Maintenance
2.1 How to Clean the Nozzle
2.2 How to Replace the Hot End
2.3 How to Replace the Screen
2.4 How to Replace the Control Board
2.5 How to Automatically Level
2.8 How to Manually Level
3 Troubleshooting
3.1 Black Screen
3.2 Update Firmware
3.3 Minimum Temperature Error
3.4 Automatic Leveling Failed
3.5 How to Import Profiles into Cura
3.6 Filament Does Not Stick to the Hot Bed
3.7 Uneven Thickness of the First Layer of Print
3.8 Prints Are Brushed or Missed
3.9 Under-Extrusion and Over-Extrusion
3.10 Insufficient Sealing of the Top Layer
3.11 Printing Offset
3.12 Surface Spots and Stripes
3.13 Gaps Between Edges and Infill
3.14 Rough Corners
3.15 Top Surface Scratches
3.16 Holes at the Bottom of the Corner
3.17 Uneven Sides
3.18 How to print TPU
3.19 How to print ABS
3.20 How to print PETG