Difference between revisions of "GT2560A/GT2560A+"
(Created page with "==Introduction== GT2560 is a compact board that is integrated with the mighty function of the Arduino Mega25 60+Ultimaker and Arduino Mega2560+ramps 1.4 on respect of both so...") |
(→Features) |
||
| Line 1: | Line 1: | ||
| − | == | + | ==Features== |
| − | + | 1.Integrated with the mighty function of the Arduino Mega2560+Ultimaker and Arduino | |
| − | + | Mega2560+ramps 1.4 kit, The GT2560 can not only take full place the them on respect of both | |
| − | + | software and hardware, but also features compact size, more convenient connection, and more | |
| − | + | stable. | |
| − | + | 2. Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial | |
| − | + | converter FT232RQ. | |
| − | + | 3. The power pack: operating voltage is 12V-24V; double power supply design feeds for | |
| − | the | + | heatbed and logical part separately. The current is 15A for heatbed and 10A for other parts. |
| − | + | 4. The main circuit adopts SMD fuse tube, the diode added to the power port can provide | |
| + | reverse protection to the whole circuit, in addition, the 5V USB is USB port protected with 500mA | ||
| + | Recoverable fuse. | ||
| + | 5． 3 12v fan output and one PWM output for LED or other lighting equipment. | ||
| + | GEEETECH | ||
| + | www.geeetech.com Tel: +86 755 2658 4110 Fax: +86 755 2658 4074 -858 | ||
| + | - 4 - | ||
| + | 6. 3 55Amp MOSFET (with LED indicator, the actual output is restricted by the PCB board | ||
| + | and the connector), all 3 MOSFET are equipped with heat sink to ensure sufficient heat dissipation | ||
| + | and stable operation. | ||
| + | 7. Support 5 A4988 stepper drivers (3 for X/Y/Z axis, and 2 for extruders); the subdivision of | ||
| + | stepper motor can be setup by dial switch, eliminating jumper caps, easier to operate. | ||
| + | 8. 3 temperature sensor input (100k thermistor is recommended) | ||
| + | 9. Extended LCD and SD card interface support both LCD2004 and LCD 12864, with which | ||
| + | you can print without your PC. | ||
| + | 10. The firmware is the prevalent Marlin, which is known for stability, usability, and | ||
| + | high-performance. | ||
Revision as of 10:40, 4 May 2018
Features
1.Integrated with the mighty function of the Arduino Mega2560+Ultimaker and Arduino Mega2560+ramps 1.4 kit, The GT2560 can not only take full place the them on respect of both software and hardware, but also features compact size, more convenient connection, and more stable. 2. Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial converter FT232RQ. 3. The power pack: operating voltage is 12V-24V; double power supply design feeds for heatbed and logical part separately. The current is 15A for heatbed and 10A for other parts. 4. The main circuit adopts SMD fuse tube, the diode added to the power port can provide reverse protection to the whole circuit, in addition, the 5V USB is USB port protected with 500mA Recoverable fuse. 5． 3 12v fan output and one PWM output for LED or other lighting equipment.
GEEETECH
www.geeetech.com Tel: +86 755 2658 4110 Fax: +86 755 2658 4074 -858 - 4 - 6. 3 55Amp MOSFET (with LED indicator, the actual output is restricted by the PCB board and the connector), all 3 MOSFET are equipped with heat sink to ensure sufficient heat dissipation and stable operation. 7. Support 5 A4988 stepper drivers (3 for X/Y/Z axis, and 2 for extruders); the subdivision of stepper motor can be setup by dial switch, eliminating jumper caps, easier to operate. 8. 3 temperature sensor input (100k thermistor is recommended) 9. Extended LCD and SD card interface support both LCD2004 and LCD 12864, with which you can print without your PC. 10. The firmware is the prevalent Marlin, which is known for stability, usability, and high-performance.
