Revision as of 04:02, 23 January 2015

Introduction

Iduino_Yun_Shield, an extremely powerful development for Arduino board, is designed to solve the problems of connection and storage which exist in the Arduino board. Iduino_Yun_Shield runs Open Source OpenWrt System (Same system as runs in Arduino Yun) and it is fully compatible with Arduino IDE V1.5.4 or later versions. Yun Shield is an ideal choice for Arduino Projects which require various internet connections and more storage.

Actually, Iduino_Yun_Shield is equal to the official Arduino Yun, but Iduino_Yun_Shield is more flexible because it can work with other Arduino board such as Uno, Duemilanove, and Mega etc. Iduino_Yun_Shield uses external antenna which provides stable connection under various environments.

The Iduino Yun is the core module of Iduino_Yun_Shield. And it requires 200mA current when in full load, so it is powered by the Arduino VIN pins to avoid overheated in the Arduino onboard 5V LD0.

Features

• Open source Linux system (OpenWrt) inside
• Low power consumption
• Compatible with Arduino IDE 1.5.4 or later versions. Users can program, debug or upload Sketch to Arduino board
• Managed by Web GUI, SSH via LAN or Wifi
• Software upgradable via network
• Support internet connection via LAN port, Wifi or 3G dongle
• Support USB flash to provide storage for Arduino projects
• Reliable design provides robust system
• Compatible with Arduino Leonardo, Uno, Duemilanove, Diecimila and Mega

Overview and Hard ware Resources

• Front image1.png

  front side
• 

  back side

1. Processor: 400MHz, 24 MIPS

2. Flash: 16MB

3. RAM: 64MB

4. Power input: 4.75V~23V via Arduino Vin pin

5. 1×10M/100M RJ45

6. Connector 150M Wifi 802.11 b/g/n

7. External antenna via I-Pex

8. 1×USB port for USB storage or 3G connection

9. 1×Reset button

10. Compatible with 3.3V or 5V I/O Arduino

Size: 70mm * 53mm*24mm

Weight: 33.2g

Software Resource

Compiling environment: Arduino IDE 1.5.4 or later version

Source

The Open Source hardware of Iduino_Yun_Shield: https://github.com/dragino/modules/tree/master/hardware/YunShield

The Open Source code of Iduino_Yun_Shield: https://github.com/dragino/linino

The official webpage of Arduino Yun Bridge: http://arduino.cc/en/Reference/YunBridgeLibrary

The official forum of Arduino Yun http://forum.arduino.cc/index.php?board=93.0

Interface

Interface layout

• 

  Interface layout
• 

  wireframe

Interface specifications

• RJ45, Wifi, USB port and Failsafe are connected to the Iduino Yun module directly, and the Iduino Yun module uses SPI and UART to communicate with Arduino board
• The SPI interface is used to upload the sketch coming from the Arduino IDE. SPI interface connects to Iduino Yun only in the upload time, so the Arduino SPI can still be used to connect to the other slave devices.
• The pins of two sides are respectively connected to the corresponding pins of Arduino

How to set up Iduino_Yun_Shield

Getting IP address

There is a Wifi interface a LAN port on the Iduino_Yun_Shield. And they both have an IP address for network connecting and device management.

Factory IP of Wifi port

At the first boot of Iduino_Yun_Shield, an unsecure Wifi network called Iduino-xxxxxx will automatically generate. Users can use their laptop to connect to this Wifi network and the laptop will get an IP 192.168.240.xxx. The default IP of Iduino_Yun_Shield is 192.168.240.1.

FallBack IP