Difference between revisions of "Brainwave"
From Geeetech Wiki
(Created page with "==Introduction==") |
(→Introduction) |
||
Line 1: | Line 1: | ||
==Introduction== | ==Introduction== | ||
+ | |||
+ | [[File:BRAINWAVE.jpg|500px|]] | ||
+ | |||
+ | Brainwave, derived from sanguinololu, is control board for reprap 3D printer with low cost and high capacity-price ratio in that it is powerful to drive a printer of single-screw extruder by providing only the minimum required components. Such as a printer with single extruder and 2 Z axis or the delta style printer. | ||
+ | |||
+ | '''Features:''' | ||
+ | |||
+ | *12v power input | ||
+ | |||
+ | *standard micro USB connector | ||
+ | |||
+ | *The entire interfaces are at the edge of the board, making it possible to fit vertical or right-angle connectors. | ||
+ | |||
+ | *Adopt Atmel AT90USB646 microcontroller, with USB- RS232. | ||
+ | |||
+ | *The steps of stepper motor can be divided into 1, 2, 16, and 32. The maximum power output can reach to 800MA | ||
+ | |||
+ | *2 connectors for Z axis | ||
+ | |||
+ | *Optional motor power output of each axis | ||
+ | |||
+ | *Heated bed supports separate power input from the logic part (up to 24V 15A) | ||
+ | |||
+ | *Integrated heater/thermistor/stepper connector for E channel | ||
+ | |||
+ | *controllable fan | ||
+ | |||
+ | |||
+ | ===Overview and Hardware Resource=== | ||
+ | |||
+ | |||
+ | size:60mm*79mm | ||
+ | |||
+ | weight:81g | ||
+ | |||
+ | |||
+ | ===Software Resources=== | ||
+ | Compiling environment: Arduino IDE http://www.geeetech.com/wiki/images/3/36/Arduino-1.0.5-r2-windows.zip | ||
+ | |||
+ | Firmware: Marlin http://www.geeetech.com/wiki/images/3/39/Marlin-Marlin_v1.zip | ||
+ | |||
+ | Pc software: | ||
+ | |||
+ | printrun http://www.geeetech.com/wiki/images/e/e1/Printrun-Win-Slic3r-10Mar2014.zip | ||
+ | |||
+ | Repetier-Host http://www.geeetech.com/wiki/images/3/36/SetupRepetierHost_1_00.zip |
Revision as of 08:41, 21 August 2014
Introduction
Brainwave, derived from sanguinololu, is control board for reprap 3D printer with low cost and high capacity-price ratio in that it is powerful to drive a printer of single-screw extruder by providing only the minimum required components. Such as a printer with single extruder and 2 Z axis or the delta style printer.
Features:
- 12v power input
- standard micro USB connector
- The entire interfaces are at the edge of the board, making it possible to fit vertical or right-angle connectors.
- Adopt Atmel AT90USB646 microcontroller, with USB- RS232.
- The steps of stepper motor can be divided into 1, 2, 16, and 32. The maximum power output can reach to 800MA
- 2 connectors for Z axis
- Optional motor power output of each axis
- Heated bed supports separate power input from the logic part (up to 24V 15A)
- Integrated heater/thermistor/stepper connector for E channel
- controllable fan
Overview and Hardware Resource
size:60mm*79mm
weight:81g
Software Resources
Compiling environment: Arduino IDE http://www.geeetech.com/wiki/images/3/36/Arduino-1.0.5-r2-windows.zip
Firmware: Marlin http://www.geeetech.com/wiki/images/3/39/Marlin-Marlin_v1.zip
Pc software:
printrun http://www.geeetech.com/wiki/images/e/e1/Printrun-Win-Slic3r-10Mar2014.zip
Repetier-Host http://www.geeetech.com/wiki/images/3/36/SetupRepetierHost_1_00.zip