Difference between revisions of "SD for RAMPS"

From Geeetech Wiki
Jump to: navigation, search
(Introduction)
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
== Introduction ==
 
== Introduction ==
  
 +
[[Image:SD for RAMPS5.jpg|500px]]
 
[[Image:SD for RAMPS3.jpg|500px]]
 
[[Image:SD for RAMPS3.jpg|500px]]
  
Line 12: Line 13:
 
*Support voltage:4.5 to 5.5V
 
*Support voltage:4.5 to 5.5V
 
*Up to 50 MB/sec data transfer rate
 
*Up to 50 MB/sec data transfer rate
*Sits directly on a Arduino
+
*Sits directly on a RAMPS
 
*Also be used with other microcontrollers
 
*Also be used with other microcontrollers
 
  
 
==Usage==
 
==Usage==
Line 46: Line 46:
 
1. Connect your SD RAMPS like this to the RAMPS board:
 
1. Connect your SD RAMPS like this to the RAMPS board:
  
 +
[[Image:SD for RAMPS6.jpg]]
 
[[Image:SD for RAMPS4.jpg]]
 
[[Image:SD for RAMPS4.jpg]]
  
Line 72: Line 73:
  
 
8. Further SD commands can be found here: http://reprap.org/wiki/Gcode#Unbuffered_M_and_T_commands
 
8. Further SD commands can be found here: http://reprap.org/wiki/Gcode#Unbuffered_M_and_T_commands
 +
 +
==How to buy==
 +
Click here: http://www.geeetech.com/sd-ramps-breakout-for-ramps-p-665.html

Latest revision as of 11:00, 27 May 2013

Introduction

SD for RAMPS5.jpg SD for RAMPS3.jpg


This RAMPS add-on enables you to print from MicroSD.With RAMPS 1.3 and higher it's easily connected to the RAMPS board.You will be able to print

without being connected to your PC.

Features

  • SPI mode
  • Support voltage:4.5 to 5.5V
  • Up to 50 MB/sec data transfer rate
  • Sits directly on a RAMPS
  • Also be used with other microcontrollers

Usage

Sometime you're not sure whether a card is working or not,you must test it.

Now,let's go.

SD card wiring.jpg

Open your arduino IDE

please click Files ->Examples ->SD ->Cardinfo


Open Serial Monitor

MICROsd.png

OK,the card is working.


RAMPS 1.3 with Sprinter firmware

These steps will guide you on how to use the SD RAMPS with RAMPS 1.3 and the Sprinter firmware.

Note that you MUST install Diode D1 on the RAMPS board if you want to be able to print without being connected to your PC - see:

http://www.geeetech.com/ramps-reprap-mega-pololu-a4988-extend-shield-p-606.html

1. Connect your SD RAMPS like this to the RAMPS board:

SD for RAMPS6.jpg SD for RAMPS4.jpg

2. Download the latest Sprinter firmware fromSprinter

Extract the firmware and open it in your Arduino IDE(00-22 ,00-23).

3. Go to the file configuration.h and change the motherboard setting:

define MOTHERBOARD 33

4. Check that SD Card support is enabled:

define SDSUPPORT 1

5. Compile and upload the firmware.

6. Open the Serial Monitor from the Arduino IDE. Make sure the left select list reads newline. Enter the GCode M21 (init SD Card). It should return ok.

SD for RAMPS1.png

7. Enter the GCode M20 (list files). It should return the contents of the SD card.

SD for RAMPS2.png


8. Further SD commands can be found here: http://reprap.org/wiki/Gcode#Unbuffered_M_and_T_commands

How to buy

Click here: http://www.geeetech.com/sd-ramps-breakout-for-ramps-p-665.html