Difference between revisions of "Megatronics V2.0"

From Geeetech Wiki
Jump to: navigation, search
(How to buy)
 
(24 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
==Introduction==
 
==Introduction==
Megatronics is based on many famous open-source products including: Arduino Mega 2560, RAMPS, SD Ramps. Therefor this product is an already proven design. It combines all major features of these board into a single board solution for more reliable 3D-printing. Megatronics has a powerful Atmega2560 processor with 256 kB memory, running at 16Mhz. The board can be connected to a PC using a normal USB cable. It will register as FTDI FT232R device. The board is compatible with the Arduino Mega 2560 and will therefor be easily programmed from the Arduino IDE.  
+
Megatronics is based on many famous open-source products including: Arduino Mega 2560, RAMPS, SD Ramps. Therefore this product is an already proven design. It combines all major features of these board into a single board solution for more reliable 3D-printing. Megatronics has a powerful Atmega2560 processor with 256 kB memory, running at 16Mhz. The board can be connected to a PC using a normal USB cable. It will register as FTDI FT232R device. The board is compatible with the Arduino Mega 2560 and will therefor be easily programmed from the Arduino IDE.
  
==SPECIFICATION==
+
==Specification==
Microcontroller: Atmega2560-16AU
+
*Microcontroller: Atmega2560-16AU
Operating Voltage Electronics:5V
+
*Operating Voltage Electronics:5V
Operating Voltage High:12-24V (15A heated bed, 7A electronics)
+
*Operating Voltage High:12-24V (15A heated bed, 7A electronics)
DC Current per I/O Pin:40mA
+
*DC Current per I/O Pin:40mA
Clock Speed:16Mhz
+
*Clock Speed:16Mhz
  
 
==Features==
 
==Features==
Line 32: Line 32:
  
 
==Interface==
 
==Interface==
 +
[[File:Megatronics03.jpg|800px]][[File:Megatronics table.jpg|400px]]
  
==Reference==
+
==wiring==
  
==Document==
+
[[File:Megatronics01.jpg]]
 +
 
 +
==Reference Design==
 +
[http://reprap.org/wiki/Megatronics_2.0 Megatronics V2.0]
 +
 
 +
==Firmware==
 +
[http://www.geeetech.com/Documents/Marlin.zip Marlin]
  
 
==How to buy==
 
==How to buy==
Click here to buy []
+
Click here to buy [http://www.geeetech.com/reprap-megatronics-v20-board-p-778.html Megatronics V2.0]

Latest revision as of 02:15, 6 February 2015

Introduction

Megatronics is based on many famous open-source products including: Arduino Mega 2560, RAMPS, SD Ramps. Therefore this product is an already proven design. It combines all major features of these board into a single board solution for more reliable 3D-printing. Megatronics has a powerful Atmega2560 processor with 256 kB memory, running at 16Mhz. The board can be connected to a PC using a normal USB cable. It will register as FTDI FT232R device. The board is compatible with the Arduino Mega 2560 and will therefor be easily programmed from the Arduino IDE.

Specification

  • Microcontroller: Atmega2560-16AU
  • Operating Voltage Electronics:5V
  • Operating Voltage High:12-24V (15A heated bed, 7A electronics)
  • DC Current per I/O Pin:40mA
  • Clock Speed:16Mhz

Features

  • Improved thermo couple support.
  • Second thermo couple supported
  • Support for 6 stepper drivers
  • SMD fuses and MOSFETs
  • Extra MOSFET, making 4 regular MOSFETs and one for heated bed.
  • Support for the new DRV8825 Pololu stepper drivers
  • The board can be powered from 12V1 (12V MAX), by setting a jumper
  • The LCD contrast can be adjusted with a trimpot
  • 12V1 has a diode to protect against reverse polarization
  • The 5V line is protected by a 500mA resettable fuse
  • A piezo is included to allow the printer to give feedback with sound
  • Each stepper driver slot has a breakout to connect external stepper drivers to the board.
  • Four layer high quality PCB board

Details

  • Thermocouple:On board support for connecting two thermo couples
  • SD Card:Autonomous printing from Micro SD card on board
  • Five MOSFETs:The board has 4 regular MOSFETs and oneMOSFET for the heated bed (IRLS3034PBF) to support many needs.
  • Up to 6 stepper drivers:Compatible with RAMPS, 6 slots for stepper drivers(not included). Modularized to make replacement easy for damaged drivers. Also the new DRV8825 Pololu stepper drivers are supported.
  • Support for many peripherals:The board's functions can be easily extended with LCD, keypad etc.

Interface

Megatronics03.jpgMegatronics table.jpg

wiring

Megatronics01.jpg

Reference Design

Megatronics V2.0

Firmware

Marlin

How to buy

Click here to buy Megatronics V2.0