Bad Base Plate Guide

bernte_one
Posts: 25
Joined: Fri Aug 24, 2018 4:39 pm

Bad Base Plate Guide

Post by bernte_one » Fri Aug 31, 2018 3:34 pm

I have received one of these defective A10. The aluminum profile of the guide of the base plate has a dent or notches. The rolls stay about every 7cm.
It is not my job to rebuild that somehow. Is there a corresponding spare part or should I send the goods back, is there proportionate money back?

I got mine Printer over ebay seller from Czech.

bernte_one
Posts: 25
Joined: Fri Aug 24, 2018 4:39 pm

Re: Bad Base Plate Guide

Post by bernte_one » Mon Sep 03, 2018 12:01 am

i made a video to show the problem
https://www.youtube.com/watch?v=uhd-zCXI1BM
:o

zonalimitatore
Posts: 78
Joined: Tue Aug 28, 2018 7:12 am
Location: Italy

Re: Bad Base Plate Guide

Post by zonalimitatore » Tue Sep 04, 2018 1:37 am

You need to adjust the 4 wheels. From video seem to be too hard and not in axys

bernte_one
Posts: 25
Joined: Fri Aug 24, 2018 4:39 pm

Re: Bad Base Plate Guide

Post by bernte_one » Tue Sep 04, 2018 8:07 pm

Nothing to adjust. Drillholes are misplaced. Bed ist Not plane. I can only adjust between loose and wobbly or hard and stiff.
IMG_20180903_212344-1305x736.jpg
IMG_20180903_212344-1305x736.jpg (140.73 KiB) Viewed 14631 times
IMG_20180903_212817-1305x736.jpg
IMG_20180903_212817-1305x736.jpg (127.25 KiB) Viewed 14631 times
IMG_20180903_212828-1305x736.jpg
IMG_20180903_212828-1305x736.jpg (156.86 KiB) Viewed 14631 times

zonalimitatore
Posts: 78
Joined: Tue Aug 28, 2018 7:12 am
Location: Italy

Re: Bad Base Plate Guide

Post by zonalimitatore » Wed Sep 05, 2018 2:13 am

doesn't matters if there is a light there. The important is the bed.
I notice le screw on left are not perpendicular.
You have to adjust these left side screw to be perpendicular,and after the right screw and set up with eccentrical

bernte_one
Posts: 25
Joined: Fri Aug 24, 2018 4:39 pm

Re: Bad Base Plate Guide

Post by bernte_one » Wed Sep 05, 2018 3:20 pm

:lol:

you can write it thousand time, but there is nothing to adjust
the drill hole for the wheel axis are misplaced several Millimeter
if i tighten it the bed slide plate is mor like a bow, but not plane
in result the the for adjusting screws for bed Level are Standing more and more non vertical

---------- heatbed
/ \ screws
--------------- slider plate

here i can Show the result of hole fail construction, a build precision i can get when cutting part from Hand by myself
https://www.youtube.com/watch?v=D9KSf5NXVHo

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Bad Base Plate Guide

Post by _kaktus_ » Wed Sep 05, 2018 3:31 pm

Hi
:mrgreen:

You have to remember one thing.
Manual movement of the mechanisms is very dangerous for electronics, even when the power supply is switched off.
;)
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

bernte_one
Posts: 25
Joined: Fri Aug 24, 2018 4:39 pm

Re: Bad Base Plate Guide

Post by bernte_one » Wed Sep 05, 2018 3:32 pm

the next joke i found yesterday after installing all, that the Extruder end stop is too far away on the left side
so Auto Zero will place the Extruder left besides the bed (5mm +/-) :?
you can´t Mount the endstop more right, because it is fixed on a plate from stepper motor :roll:
so only solution i can do is to place a spacer between endstop Switch and the Extruder carrier to Bridge 5mm+/- :cry:

so from that what i have compred on YouTube i got the crappiest a10 pinter for now

These hole supporters from YouTube which got These Printer for free or other Special condition should be shame themself
they got Special checked and best made Printers for Promotion

but the normal user got frustrating fail production?

bernte_one
Posts: 25
Joined: Fri Aug 24, 2018 4:39 pm

Re: Bad Base Plate Guide

Post by bernte_one » Wed Sep 05, 2018 3:37 pm

_kaktus_ wrote:
Wed Sep 05, 2018 3:31 pm
Hi
:mrgreen:

You have to remember one thing.
Manual movement of the mechanisms is very dangerous for electronics, even when the power supply is switched off.
;)
and how did you Level your bed? :lol:

and know the fact, but manuel say: Switch on, go to menue, disable stepper, and adjust bed on several Points....

better you tell this manufacturer, that they add a kill Switch for the stepper power line for leveling procedure?

zonalimitatore
Posts: 78
Joined: Tue Aug 28, 2018 7:12 am
Location: Italy

Re: Bad Base Plate Guide

Post by zonalimitatore » Wed Sep 05, 2018 9:15 pm

Image
Image

Post Reply