BLTouch???

Post Reply
Benfish65
Posts: 4
Joined: Wed Jul 18, 2018 8:02 am

BLTouch???

Post by Benfish65 » Wed Jul 18, 2018 8:05 am

Hello everyone!

I have the MC2 and it has the GT2560 Rev B control board. Is it possible to add a BLTouch to this printer? Will I have to do anything with the firmware to turn auto leveling on?

Thanks to all who reply!
Top
Gingko
Site Admin
Posts: 230
Joined: Tue Apr 24, 2018 10:43 am

Re: BLTouch???

Post by Gingko » Tue Jul 24, 2018 4:25 pm

It's possible, you can try it.
In their user manual, there might be an introductions of firmware setting.
Attachments
GT2560 RevB+3D Touch.jpg
GT2560 RevB+3D Touch.jpg (323.11 KiB) Viewed 15501 times
Top
Wolle82
Posts: 48
Joined: Thu Sep 06, 2018 9:19 am

Re: BLTouch???

Post by Wolle82 » Sun Oct 07, 2018 7:05 am

Wrong
Top
User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:
Contact _kaktus_

Re: BLTouch???

Post by _kaktus_ » Sun Oct 07, 2018 1:28 pm

Wolle82 wrote: ↑
Sun Oct 07, 2018 7:05 am
Wrong
:lol:

Your person can contribute a lot of good to the forum. :D
But only in one case. When you change your attitude and you will be more helpful to the community. :roll:

Would you like to expand on the topic and present your remarks :?:
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Top
Wolle82
Posts: 48
Joined: Thu Sep 06, 2018 9:19 am

Re: BLTouch???

Post by Wolle82 » Thu Nov 22, 2018 10:32 pm

Easy... the orange one is the signal one. As I know red and orange here must be swaped.
Top
User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:
Contact _kaktus_

Re: BLTouch???

Post by _kaktus_ » Fri Nov 23, 2018 12:56 am

:mrgreen:
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Top
Gingko
Site Admin
Posts: 230
Joined: Tue Apr 24, 2018 10:43 am

Re: BLTouch???

Post by Gingko » Fri Nov 23, 2018 7:21 pm

Wolle82 wrote: ↑
Thu Nov 22, 2018 10:32 pm
 Easy... the orange one is the signal one. As I know red and orange here must be swaped.
Yes, you are correct! And sorry, I should double check.
Top
Post Reply

Return to “Geeetech MeCreator2”