-
Laeriut
- Posts: 5
- Joined: Sat Dec 03, 2016 3:31 pm
Post
by Laeriut » Fri Dec 16, 2016 4:38 am
Hi all
I have the 3D touch leveling sensors. I have the GT2560 board but not like in the description. So now i dont know how to wire the sensors. I cant solder the 3 pins on ZMAX because there are only 2. How can i wire the sensors on the board? Show attachement, this are my endstops on the board.
Thanks
-
Attachments
-
- 20161215_213740.jpg (654.68 KiB) Viewed 17458 times
-
Cup
- Posts: 123
- Joined: Fri Jul 15, 2016 6:11 pm
Post
by Cup » Fri Dec 16, 2016 9:23 am
Laeriut wrote:Hi all
I have the 3D touch leveling sensors. I have the GT2560 board but not like in the description. So now i dont know how to wire the sensors. I cant solder the 3 pins on ZMAX because there are only 2. How can i wire the sensors on the board? Show attachement, this are my endstops on the board.
Thanks
Hi,
Did you read the User Manual of 3D touch?
You need remove the Z_max connector then solder another 3-pin connector to replace it,otherwise you can't get your sensor working i guess:
- Catch45DD(12-16-09-14-59).jpg (180.39 KiB) Viewed 17451 times
-
Laeriut
- Posts: 5
- Joined: Sat Dec 03, 2016 3:31 pm
Post
by Laeriut » Fri Dec 16, 2016 2:18 pm
Yes i read the manual. But i have a different board... i dont have 3 connectors on the board to solder a 3pin header... look at the picture, my endstop connectors are all facing parallel to the board. On the board in the description they are 90° degrees otherwise.
-
Laeriut
- Posts: 5
- Joined: Sat Dec 03, 2016 3:31 pm
Post
by Laeriut » Fri Dec 16, 2016 7:58 pm
I fixed my Problem. I am now able to use the sensors (without soldering anything).
-
Cup
- Posts: 123
- Joined: Fri Jul 15, 2016 6:11 pm
Post
by Cup » Sat Dec 17, 2016 4:06 pm
Nice work!
How did you make it?
-
Laeriut
- Posts: 5
- Joined: Sat Dec 03, 2016 3:31 pm
Post
by Laeriut » Mon Dec 19, 2016 6:04 am
5v from pin of the Stepper driver and GND and control signal from Z-MAX
-
Akroon
- Posts: 4
- Joined: Wed Jan 25, 2017 6:22 pm
Post
by Akroon » Wed Jan 25, 2017 6:25 pm
Laeriut wrote:5v from pin of the Stepper driver and GND and control signal from Z-MAX
That sounds like a great solution, cause I'm to scared too solder on my board.
is it possible for you two take a photo of your wiring? Which stepper driver pin you used?
-
Romuald
- Posts: 1
- Joined: Wed Mar 29, 2017 11:06 pm
Post
by Romuald » Thu Apr 13, 2017 9:52 pm
[quote="Laeriut"]5v from pin of the Stepper driver and GND and control signal from Z-MAX :)[/quote]
I have the same issue can you take a picture of the wires please ?
EDIT : Connection wires solved for me, i have found a pdf files who have an update picture for the "GT2560 Rev a+" board, see the picture below for understand how to connect
[img]
http://i.imgur.com/E0t34VU.png[/img]
Last edited by
Romuald on Sun Oct 15, 2017 11:49 pm, edited 1 time in total.
-
William
- Site Admin
- Posts: 6340
- Joined: Tue Jun 07, 2016 9:38 am
Post
by William » Tue May 02, 2017 8:40 am
Hi,there are 3 pins on ZMax 's location.You just need to replace the 2pins' socket with 3pins.
-Keep your mind and try to test it.
-Everything will be fun！-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
