Rostock 301, new firmware changelog

[raoulito9]

Hi
There is a new firmware for rostock 301.
ROSTOCK301_V1.0.0.2.zip
(63.6 KiB) Downloaded 29 times

Can you give us the changelog ?
Is it worth burning ?

[William]

It repaired some bugs,including the stoping in half of the printing process and failing to read SD card.

[flintewn]

As i mentionned in another post, release the source code, you are using marlin who is under GNU GPL v3.

[JohnQuix]

Is there a reason this printer doesn't just run a regular open version of Marlin like the rest of your printers?

This type of hot end has been supported in Marlin for awhile now so it can't be that anymore.

If you guys make it a regular Marlin that we can self service it will save Geeetech a lot of support issues.

[Lami René]

Hello,
Bonjour,

You will find the original text translated into English following this original French text.

Vous trouverez le texte original traduit en anglais à la suite du présent texte original en français.

Pourriez-vous demander à vos plus hauts responsables de libérer le code source de la carte contrôleur GTM32 Pro de l'imprimante 3D delta Geeetech 301 (M301) ?

C'est une demande officielle pour vos plus hauts responsables !

Merci d'avance pour toutes les démarches que vous ferez pour cela !

Cordialement,

L'ami René
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Hello,

Excuse me, I am unilingual francophone and I use Google translator to translate the texts of the forum in French and to write to you in English. Thank you for your understanding and your indulgence for these texts translated mechanically!

Could you ask your top managers to release the source code of the controller card GTM32 Pro 3D printer delta Geeetech 301 (M301)?

This is an official request for your top managers !

Thank you in advance for all the steps you will make for this!

Cordially,

Friend René

Lami René

[JohnQuix]

It is definitely Marlin which means the source code is required to be openly available.

We would still need a way to turn the code into a file that would be flashable for an stm32 based system.

[Lami René]

Hello JohnQuix,
Bonjour JohnQuix,

You will find the original text translated into English following this original French text.

Vous trouverez le texte original traduit en anglais à la suite du présent texte original en français.

Oui, c'est l'IDE Arduino qui est disponible pour les systèmes d'exploitation Linux, Mac OS et MS-Windows.

Voir : https://www.arduino.cc/en/Main/Software

Cordialement,

L'ami René
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Hello JohnQuix,

Excuse me, I am unilingual francophone and I use Google translator to translate the texts of the forum in French and to write to you in English. Thank you for your understanding and your indulgence for these texts translated mechanically!

Yes, the Arduino IDE is available for Linux, Mac OS and MS-Windows operating systems.

See: https://www.arduino.cc/en/Main/Software

Cordially,

Friend René

[JohnQuix]

I don't think that the GTM32 speaks to Arduino IDE

[flintewn]

That's the point raised by rené.
theyhave used marlin to create the firmware, why the stm32 did not use arduino ide ?

[JohnQuix]

I think if we were able to edit the firmware ourselves it would probably save Geeetech a lot of tech support problems.