For people who wants STL files of parts

Buzz · Post by **Buzz** » Thu Jul 09, 2015 6:19 pm

Thank you for the attention and fast response, Eric.

leo · Post by **leo** » Wed Jul 15, 2015 5:05 am

I purchased your dual extruder and am installing it on a Prusa i3 printer. The dual extruder holder stl file does not fit the dual extruder I purchased. You have no heatsinks and one fan on the extruder provided with your pro c printer kit but the dual extruder you sell separately has 2 heatsinks and two fans so it won't fit the holder. Is it ok to install without the heatsinks? Why 2 different versions of the same thing? No stl file for a holder that will fit mine?

Thanks

The3DStudent · Post by **The3DStudent** » Wed Jul 15, 2015 6:25 am

Are the printed parts (stl files) for the Prusa i3 pro C the same as the i3 B? I realize the dual extruder mount is already listed separately, but I do not see a listing for the other i3 C parts. If they are not the same could you please post them or send them in an email?

On another note, this thread is not the easiest thing to find and does not appear when searching the forums for "stl". Perhaps you could put a link to this thread in the build instructions or on the webpage for each of these printers. A better solution would be to add a "downloads" section to your main page or to each printer's webpage; in this section you could provide stl files as well as firmware files saving everyone a great deal of time.

the3dstudent@gmail.com

Sherry · Post by **Sherry** » Wed Jul 15, 2015 4:39 pm

leo wrote:I purchased your dual extruder and am installing it on a Prusa i3 printer. The dual extruder holder stl file does not fit the dual extruder I purchased. You have no heatsinks and one fan on the extruder provided with your pro c printer kit but the dual extruder you sell separately has 2 heatsinks and two fans so it won't fit the holder. Is it ok to install without the heatsinks? Why 2 different versions of the same thing? No stl file for a holder that will fit mine?

Thanks

hi,could you take a picture of you new dual extruder and heat sink?

Sherry · Post by **Sherry** » Wed Jul 15, 2015 5:00 pm

hi,these stl files are the same,could you please take a picture of "mount" and "thread" in the review.i'm not sure whict part you describe.thx.

The3DStudent · Post by **The3DStudent** » Thu Jul 16, 2015 1:24 pm

"Thread" == forum topic/question and all associated replies

Which stl files are for the Prusa i3 pro C with dual mk8 extruders(see link below)?
http://www.geeetech.com/unassembledgeee ... p-927.html

plee1024 · Post by **plee1024** » Wed Dec 09, 2015 3:40 am

Are the i3x .STL parts availabe?

Mark · Post by **Mark** » Wed Dec 09, 2015 2:03 pm

I3 X have no printed plastic parts so there's no stl files for it.

chase · Post by **chase** » Fri Jul 22, 2016 2:04 am

Hi,

Which if any of the above be for an 8mm Acrylic i3 Pro B and C?

tia

Post by **William** » Fri Jul 22, 2016 10:17 am

chase wrote:Hi,

Which if any of the above be for an 8mm Acrylic i3 Pro B and C?

tia

Hi,
What your "8mm" means?

Geeetech

For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts

Re: For people who wants STL files of parts