Printer dead? (Acrylic Geeetech I3 pro B)

Post Reply
3d Printer Noob
Posts: 7
Joined: Thu Apr 09, 2015 9:04 am

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by 3d Printer Noob » Mon Apr 13, 2015 7:36 pm

Image of switch - connections are good.
Attachments
2015-04-13 07.29.49.jpg
2015-04-13 07.29.49.jpg (600.22 KiB) Viewed 11303 times
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by zhangxueyou » Tue Apr 14, 2015 2:55 pm

3d Printer Noob wrote:Image of switch - connections are good.
Please contact customer service.
Top
cazuroweste
Posts: 15
Joined: Tue Mar 31, 2015 9:41 am

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by cazuroweste » Thu May 21, 2015 3:03 am

I have the exact same problem now. A couple weeks ago i received my replacement sanguinololu, after it was determined the z axis was shot, and then put it back together with new z axis threaded rods. I fired it up, leveled the bed, and started printing. 25minutes into the print, the green led went off, then just glowed while it was plugged into the pc. Everything else stopped. There is no voltage coming off the power supply at all. It seems this printer is plagued with problems.
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by zhangxueyou » Thu May 21, 2015 2:43 pm

cazuroweste wrote:I have the exact same problem now. A couple weeks ago i received my replacement sanguinololu, after it was determined the z axis was shot, and then put it back together with new z axis threaded rods. I fired it up, leveled the bed, and started printing. 25minutes into the print, the green led went off, then just glowed while it was plugged into the pc. Everything else stopped. There is no voltage coming off the power supply at all. It seems this printer is plagued with problems.
You said you plug your printer into pc when it's printing? Ofcourse that will stop the printing.
Top
cazuroweste
Posts: 15
Joined: Tue Mar 31, 2015 9:41 am

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by cazuroweste » Fri May 22, 2015 4:32 am

It's always plugged into the usb, that's how repetier runs and sends the code.
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by zhangxueyou » Fri May 22, 2015 9:03 am

cazuroweste wrote:It's always plugged into the usb, that's how repetier runs and sends the code.
How about printing off line by SD card?
Top
cazuroweste
Posts: 15
Joined: Tue Mar 31, 2015 9:41 am

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by cazuroweste » Fri May 22, 2015 10:29 am

Won't turn on at all. The power supply is dead.
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by zhangxueyou » Fri May 22, 2015 10:46 am

Can you get 2 groups of 12V out put voltage from power supply?
Top
cazuroweste
Posts: 15
Joined: Tue Mar 31, 2015 9:41 am

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by cazuroweste » Fri May 22, 2015 10:52 am

No output from the power supply. Multimeter confirms it is not working.
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: Printer dead? (Acrylic Geeetech I3 pro B)

Post by zhangxueyou » Fri May 22, 2015 11:30 am

cazuroweste wrote:No output from the power supply. Multimeter confirms it is not working.
It seems dead, if wiring is correct.
Top
Post Reply

Return to “Others”