problem on iduino mega 2560 undetected

Post Reply
kris.mao
Posts: 22
Joined: Tue Dec 23, 2014 10:47 am

Re: problem on iduino mega 2560 undetected

Post by kris.mao » Thu Jan 15, 2015 10:01 am

Dear friend,
You can try to re-boot the firmware of 16U2 IC,sometimes this method is effective.
Please kindly try this.

Best Wishes!
Top
kevbme
Posts: 7
Joined: Fri Apr 04, 2014 11:10 pm

Re: problem on iduino mega 2560 undetected

Post by kevbme » Mon Jan 19, 2015 7:14 am

kris.mao wrote:Dear friend,
You can try to re-boot the firmware of 16U2 IC,sometimes this method is effective.
Please kindly try this.

Best Wishes!
I am having this problem on my rumba. How do you reboot the firmware?
Top
kevbme
Posts: 7
Joined: Fri Apr 04, 2014 11:10 pm

Re: problem on iduino mega 2560 undetected

Post by kevbme » Mon Jan 19, 2015 7:17 am

I am having this problem on my rumba. How do you reboot the firmware
Top
kris.mao
Posts: 22
Joined: Tue Dec 23, 2014 10:47 am

Re: problem on iduino mega 2560 undetected

Post by kris.mao » Mon Jan 19, 2015 3:19 pm

Hi，kevbme
Could you give us more detail about your problem? This wil help us to give you a better solution.
Looking forward to your reply,Thanks!

Best regards!
Top
kevbme
Posts: 7
Joined: Fri Apr 04, 2014 11:10 pm

Re: problem on iduino mega 2560 undetected

Post by kevbme » Tue Jan 20, 2015 12:01 pm

When I plug the USB to the board, it gets power but will not connect to the computer. I have the jumper in the correct place. I tried using the USB pins instead of the plug and that did not work either.
Top
kris.mao
Posts: 22
Joined: Tue Dec 23, 2014 10:47 am

Re: problem on iduino mega 2560 undetected

Post by kris.mao » Tue Jan 20, 2015 5:23 pm

Dear friend,
Maybe you can try this method first
1.Please make sure the USB cord is connected well
2, check if all the jumper caps are plugged as required
3, is the driver well installed?
if you still have any questions, please try to re-burn the 16U2

Best regards!
Top
kevbme
Posts: 7
Joined: Fri Apr 04, 2014 11:10 pm

Re: problem on iduino mega 2560 undetected

Post by kevbme » Tue Jan 20, 2015 10:41 pm

I have done all of those things. can you give me instructions on how to burn it with an Arduino uno?
Top
kris.mao
Posts: 22
Joined: Tue Dec 23, 2014 10:47 am

Re: problem on iduino mega 2560 undetected

Post by kris.mao » Wed Jan 21, 2015 10:43 am

Dear friend,
Tools needed for burning 16U2: USBISP, burning software( e.g. ProgISP172) . download the firmware here:http://www.reprap.org/wiki/RUMBA
1, connect the 2 pins on" Stand alone" with jumper caps to supply external power.
2. connect the ISP2 of RUMBA to your PC with USBISP, note the direction.
3, open the burning software. choose 16U2 . set the Fuse point.
4, upload the firmware you have downloaded, click " auto" to go on

Best regards!
Top
kevbme
Posts: 7
Joined: Fri Apr 04, 2014 11:10 pm

Re: problem on iduino mega 2560 undetected

Post by kevbme » Wed Jan 21, 2015 11:33 pm

Can you label what each of these pins are for me please? I will be using jumpers to do this and need to know what the individual pins are.
RUMBA Pins.jpg
RUMBA Pins.jpg (243.08 KiB) Viewed 15545 times
Top
kris.mao
Posts: 22
Joined: Tue Dec 23, 2014 10:47 am

Re: problem on iduino mega 2560 undetected

Post by kris.mao » Thu Jan 22, 2015 11:23 am

Hi!
1.jumper cap: connect the 2 pins on" Stand alone" with jumper caps
2.16U2 ISP: connect the "16U2 ISP" of RUMBA to your PC with USBASP, note the direction.
(1:+5V 2:MOSI 3:GND 4:MISO 5: SCK 6:RESET )

Best regards!
RUMBA_16u2_ISP.jpg
RUMBA_16U2_ISP
RUMBA_16u2_ISP.jpg (49.64 KiB) Viewed 15541 times
Top
Post Reply

Return to “Open Hardware”