Geeetech A10 - Powers on but lcd does not work
Geeetech A10 - Powers on but lcd does not work
Hi
I recently got the Geetech A10 and have had a good few sucessfull prints but today i took apart the hot end to unclog it and i think it blew something. The printer powers up and i can hear the fan in running but the lcd does not power on so i cant check if it will heat up or select anything.
Really not sure what the issue is i have seen some on this forum and people asking for a picture of the motherboard lights so i have attached an image of that
Hope somebody can help i really want to get back to printing
thanks in advance for any replies
Ryan
I recently got the Geetech A10 and have had a good few sucessfull prints but today i took apart the hot end to unclog it and i think it blew something. The printer powers up and i can hear the fan in running but the lcd does not power on so i cant check if it will heat up or select anything.
Really not sure what the issue is i have seen some on this forum and people asking for a picture of the motherboard lights so i have attached an image of that
Hope somebody can help i really want to get back to printing
thanks in advance for any replies
Ryan
- Attachments
-
- 94270256_660352988150076_6177028527817228288_n.jpg (434.44 KiB) Viewed 6055 times
Re: Geeetech A10 - Powers on but lcd does not work
Hi,you can check whether the line is not connected refer to this:
viewtopic.php?f=23&t=17040
viewtopic.php?f=23&t=17040
-Keep your mind and try to test it.
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
Re: Geeetech A10 - Powers on but lcd does not work
Hey, So i have checked the voltage on the main board with a multimeter (I am a novice so not sure i've done it right) to get a consistent reading i have to set it to dcv 200 and it comes out as 24 which seems a bit off but that's what i get. Again not sure if i have done that right so bare with me
thanks Ryan
thanks Ryan
Re: Geeetech A10 - Powers on but lcd does not work
Hi,my friend, can you tell me where you are measuring the voltage on the motherboard?
-Keep your mind and try to test it.
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
Re: Geeetech A10 - Powers on but lcd does not work
Hey,
These are the two points i tried to measure from like i said i wasn't too sure where exactly i should be measuring from. I did test the multimeter on a battery to make sure that it worked and it did give me the right reading, so at least i know that the multimeter does work
thanks Ryan
These are the two points i tried to measure from like i said i wasn't too sure where exactly i should be measuring from. I did test the multimeter on a battery to make sure that it worked and it did give me the right reading, so at least i know that the multimeter does work
thanks Ryan
- Attachments
-
- image_motherboard.jpg (570.89 KiB) Viewed 5973 times
Re: Geeetech A10 - Powers on but lcd does not work
Hi,your motherboard is broken, you can replace the motherboard.
-Keep your mind and try to test it.
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
Re: Geeetech A10 - Powers on but lcd does not work
Thanks for your help
I thought that might have been the case, I have noticed some frayed wires around the hot end so i think that might have blown it. SO i think i'm going to replace that too
Thanks again Ryan
I thought that might have been the case, I have noticed some frayed wires around the hot end so i think that might have blown it. SO i think i'm going to replace that too
Thanks again Ryan