Unresponssive printer and crc errors

[Panormitis]

Hello, I have a Geeetech A10M for about a year. It was working fine. I tinkered and uploaded the firmware numerous times in the past with no problems.
However after the last firmware install, the printer became unresponsive and throws a lot of crc errors. Any ideas how to fix it?

Slic3r.png (62.39 KiB) Viewed 4004 times

Code: Select all

echo: External Reset
Marlin 1.1.8
echo: Last Updated: 2017-12-25 12:00 | Author: (none, default config)
echo:Compiled: Jan 13 2020
echo: Free Memory: 2432  PlannerBufferBytes: 1360
echo:V12 stored settings retrieved (642 bytes; crc 36404)
echo:poweroff stored settings retrieved (56 bytes; crc 0)
read file dir: 
read file name: 
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0
crc error: 10 != 0

[William]

Hi,you can try to :1.Go to the octoprint settings;

2.In the settings under Serial connection -> Behavior -> Cancel current print jobs and then execute M500 in the terminal.

and you can refer to this:https://github.com/OctoPrint/OctoPrint- ... /issues/42

I hope this can help you.

[Panormitis]

I tried other versions of firmware, I tried upgrading with and without an sd card. Didn't make any difference. I tried M502 & M500, no luck.
The screen & menus are unusable.
How many rewrites can the eeprom handle?
I'm not using octoprint

IMG_7676.JPG (212.94 KiB) Viewed 3997 times

[William]

Hi, Can you upload it using the firmware that has been compiled on the official website?

Upload using firmware toolkit,
You can refer to: viewtopic.php?f=20&t=69684
You need to close the slicing software when uploading to avoid occupying the port.

[Panormitis]

I usually upgrade the firmware from Linux using Arduino IDE, with no issues so far. However when I used Windows and the firmware toolkit, the printer worked again, thanks.
I guess something went wrong with the usb drivers on Linux.

I have another problem too, I'll open a new thread for it.

[Panormitis]

Thanks for the info Vert