3d touch with Prusa I3 W

Katsuki · Post by **Katsuki** » Sun Sep 01, 2019 6:28 am

I've got a 3d touch ready to go into my new I3 w, but im having issues seeing how to wire it in.
The manual on the wiki shows to desolder the 3 pin axis limit connector my my board only has 2 pin axis limit connectors.
Can anyone advise?

Post by **William** » Mon Sep 02, 2019 9:36 am

Hi, you can refer to this:http://www.geeetech.com/wiki/index.php/ ... ing_Sensor

Katsuki · Post by **Katsuki** » Tue Sep 03, 2019 5:21 am

The board shown in this guide isnt the same as mine.

The board in the guide shows the headers to be 2 pin, then 3 pin, then 2, then 3 then 2 then the one you wire into.

On my board the headers are all 2 pins only. see below

https://imgur.com/a/zr8xNTw

Post by **William** » Tue Sep 03, 2019 9:45 am

Hi， Hi, If you want to connect 3D touch to the motherboard,
you need to remove the Z max connector from the board and replace it with a 3Pin Straight Pin.
You need to use soldering iron here.
I hope this can help you.

Katsuki · Post by **Katsuki** » Fri Sep 06, 2019 2:40 pm

Ok, I removed the header and soldered the 3 pin connection in. I have it all connected and I uploaded new firmware with the changes as per the manual and my 3d touch doesn't do anything? No self test or anything. The red light comes on if I nudge the pin up and goes off if I pull it down but nothing else.

I've checked using the endstop status command and it isn't seeing it change either

Post by **William** » Fri Sep 06, 2019 2:58 pm

Hi, When you connect 3d touch, you don't need to install the z-axis limit switch.
Are you updating the Marlin firmware with 3D Touch using the Arduino version 1.0.1?

If all of the above have been tried, there is still a problem,
Specific videos can be provided.
So that we can solve the problem better.

Katsuki · Post by **Katsuki** » Fri Sep 06, 2019 4:13 pm

So I contact where i bought the device from and they say i don't need to solder 3 pins as there is a 3 pin header down near the thermistor connections I should use? does this make sense?

Post by **William** » Fri Sep 06, 2019 4:24 pm

maybe you refer to this:

: $%5`IO)CUE$6WY(K{V7{[P5.png (139.95 KiB) Viewed 12486 times

It's for A10/A20series.

Katsuki · Post by **Katsuki** » Fri Sep 06, 2019 4:28 pm

I asked, they refer to this

https://i.ebayimg.com/images/g/y7YAAOSw ... -l1600.jpg

Katsuki · Post by **Katsuki** » Fri Sep 06, 2019 4:34 pm

This is the board I have, I've connected it up this way and it doesn't respond to test codes, I assume this is because the pin is different do you know the pin number, or would you advise to use the top header only

Geeetech

3d touch with Prusa I3 W

3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W

Re: 3d touch with Prusa I3 W