A few months back I bought a geeetech a10m from internet. The package was good and the pieces arrived in good shape.
After screwing and assemble the printer I made some tests. Of course the quality of the pieces wasn´t very good so I dedicated a lot of updating the firmware, adjust the screws of the extruder, perfectly level the bed, cleaning the axis, adjusting the steps on the memory (since the original number is wrong from factory) and made a deep cleaning.
Nothing has changed in the quality, there are layer shifts, a lot of stringing, under extrusion even with a ridiculous amount of flow. I tried changing the filament brands, a lot of parameters and slicers but I can get a good quality print.
Hope someone can help me.
Geeetech A10M, bad printing since purchase
-
Pajarobergaz
- Posts: 2
- Joined: Sat Aug 24, 2019 5:42 am
Re: Geeetech A10M, bad printing since purchase
Hi, Can you provide a quality picture of the model you printed or a video when you printed it?
So that we can solve the problem better.
So that we can solve the problem better.
-Keep your mind and try to test it. 
-Everything will be fun！-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
-Everything will be fun！-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
Re: Geeetech A10M, bad printing since purchase
i HAVE THE SAME PROBLEMS SINCE JANUARY WITH MY A10 !
-
Pajarobergaz
- Posts: 2
- Joined: Sat Aug 24, 2019 5:42 am
Re: Geeetech A10M, bad printing since purchase
I would like to post a picture, but I don´t have the patience to know how to use the ![Image]()
for this forum.
I gave a last chance to the printer following this post: https://www.geeetech.com/forum/viewtopi ... 6&start=10. However, the screws wont get out (tried to remove them 3 whole days) and it looks like the nozzle is perma-clogged.
The part I hate the most is "it is true they are intended as anti back flow but it is also true these disks are the direct cause of 100s of other issues and when there removed there are zero noted draw backs.
they need to stop putting these disks in at the factory they are self sabotaging there own products with them.
many of my discord users have done this and all of there issues went away and had no issues since its been many months since they did this." - Vert.
It clearly looks like Geeetech doesn´t know how to make quality products. At least, my printer didn´t work properly after 6 months working on it. The structure its ok (maybe) but the extruder is trash.
I feel I wasted my money with this printer.
I gave a last chance to the printer following this post: https://www.geeetech.com/forum/viewtopi ... 6&start=10. However, the screws wont get out (tried to remove them 3 whole days) and it looks like the nozzle is perma-clogged.
The part I hate the most is "it is true they are intended as anti back flow but it is also true these disks are the direct cause of 100s of other issues and when there removed there are zero noted draw backs.
they need to stop putting these disks in at the factory they are self sabotaging there own products with them.
many of my discord users have done this and all of there issues went away and had no issues since its been many months since they did this." - Vert.
It clearly looks like Geeetech doesn´t know how to make quality products. At least, my printer didn´t work properly after 6 months working on it. The structure its ok (maybe) but the extruder is trash.
I feel I wasted my money with this printer.
Re: Geeetech A10M, bad printing since purchase
Try to use my printing profile
A10M Slic3r profile: here and fresh on github (lot of tips here)
A10 Slic3r profile: here
TIP: tight all screws and wheels (except right side of Z axis) and re-align frame while assembly. And silence it.
A10 Slic3r profile: here
TIP: tight all screws and wheels (except right side of Z axis) and re-align frame while assembly. And silence it.