Page 1 of 3
3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Tue Oct 02, 2018 5:53 am
by Wolle82
Hi there ...
Mainboard: GT2560 Rev B
Printer: Geeetech A10
Sensor: BLTouch
after I connected the autoleveling sensor it seams to look quiet good. It starts its selftest and there is no alert blinking. All okay so far. I did the changes to the firmware to activate the BLTouch (ABL). But when I start testing it doesn't do anything. The GCODE commands end with "OK" in the log, but nothing happens. I connected the sensor this way:
viewtopic.php?f=91&t=61576&start=10.
"M280 P0 S10" for example... nothing happen.
Any ideas? May you help me please?
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Sat Oct 06, 2018 4:05 am
by Wolle82
No ideas?
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Sat Oct 06, 2018 4:45 am
by RepMike
I hope you get a reply from Geeetech soon. Please note that due to the Chinese National day, many companies in China are on holiday for the entire week. Maybe it's also the case with GT; I don't know though. I just wanted to encourage you to be patient.
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Thu Dec 06, 2018 10:05 pm
by zonalimitatore
Any news?
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Fri Dec 07, 2018 1:56 am
by Rainerw
Same problem, i dont get this GT2560 RevB work with BLtoch. BLTouch do a self test after turning printer on, and thats it. No control in BLTouch Menu or with Gcode.
I tried this
http://www.geeetech.com/forum/viewtopic ... 6&start=10
and
https://cdn.thingiverse.com/assets/05/0 ... to_A10.pdf
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Fri Dec 07, 2018 2:28 am
by zonalimitatore
Fantastic....i've order one other day
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Fri Dec 07, 2018 2:58 am
by Rainerw
zonalimitatore wrote: ↑Fri Dec 07, 2018 2:28 am
Fantastic....i've order one other day
Now you get the GT2560 V3.0 Controller Board
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Fri Dec 07, 2018 4:14 am
by zonalimitatore
Rainerw wrote: ↑Fri Dec 07, 2018 2:58 am
zonalimitatore wrote: ↑Fri Dec 07, 2018 2:28 am
Fantastic....i've order one other day
Now you get the GT2560 V3.0 Controller Board
i've rev b
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Mon Dec 17, 2018 2:28 am
by zonalimitatore
Mount....follow how install,add parameters to firmware,reflash,aaaaaaaand.....not work. No control in menu
Geeeeeeetech....there is a way to make it work or it's lost time?
Re: 3DTouch / BLTouch auto leveling sensor GCODE for GT2560 Rev B
Posted: Mon Dec 17, 2018 2:45 am
by zonalimitatore
I've write my own firmware,and I haven't filament sensor enable.
