Page 1 of 8
Geeetech A10 firmware Marlin 1.1.9
Posted: Fri Aug 24, 2018 12:04 am
by MichaelK
Now, i present my new firmware for the Geeetech A10 with Marlin 1.1.9 now.
Functions:
- Language english
- manual Bed Leveling over 9 Points activated
- automatic Z adjustment at printing
A10 Firmware on Thingiverse
Using without any warranty an on your own risk!
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Fri Aug 24, 2018 12:06 am
by _kaktus_
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Fri Aug 24, 2018 4:45 pm
by bernte_one
Hi Michael,
i bought the A10 in result of reading your blog.
would you pls be so Kind to write a short guide how to flash the Firmware (maybe in german on your blog) or here in Forum
My Printer will arrive next week from Czech, so the guide has not the highest prority for me, but i hope to see it on monday
no, was a joke
best regards Bernd
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Fri Aug 24, 2018 5:40 pm
by MichaelK
Of course! Many people ask me about how to install the firmware.
There a many possibilities and one of them is the easiest way to do it!
One of my remaining points is to write a tutorial to install a new firmware.
Please have some patience.
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Fri Aug 24, 2018 10:46 pm
by MichaelK
bernte_one:
so the guide has not the highest prority for me, but i hope to see it on monday
no, was a joke
I'am faster
Into my blog you found a description easy to update the firmware.
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Mon Aug 27, 2018 11:21 pm
by MichaelK
Update: New version on thingiverse.
I found a small bug into the firmware with the cooling fan to cooling up the printing object.
Bug fixed now.
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Tue Aug 28, 2018 7:16 am
by zonalimitatore
Hello everyone...
This firm it's ready for install o i need edit config in arduino ide?
Or simply click on marlin.ino and upload on board?
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Tue Aug 28, 2018 12:19 pm
by MichaelK
zonalimitatore wrote: ↑Tue Aug 28, 2018 7:16 am
Hello everyone...
This firm it's ready for install o i need edit config in arduino ide?
Or simply click on marlin.ino and upload on board?
If you need to change any functions into Marlin you need to use the arduino ide to do it.
You can use many ways to install the firmware.
two possebilities:
1: Arduino IDE, conect the printer with Pc, start arduino with the marlin.ino and save them onto the printer directly.
2: use xloader
http://russemotto.com/xloader/ to install the .hex File onto the printer.
I think, the second way is easier....
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Tue Aug 28, 2018 6:29 pm
by zonalimitatore
MichaelK wrote: ↑Tue Aug 28, 2018 12:19 pm
zonalimitatore wrote: ↑Tue Aug 28, 2018 7:16 am
Hello everyone...
This firm it's ready for install o i need edit config in arduino ide?
Or simply click on marlin.ino and upload on board?
If you need to change any functions into Marlin you need to use the arduino ide to do it.
You can use many ways to install the firmware.
two possebilities:
1: Arduino IDE, conect the printer with Pc, start arduino with the marlin.ino and save them onto the printer directly.
2: use xloader
http://russemotto.com/xloader/ to install the .hex File onto the printer.
I think, the second way is easier....
Danke.
So i just upload it without config.All config for A10 it's already set?
Re: Geeetech A10 firmware Marlin 1.1.9
Posted: Tue Aug 28, 2018 7:02 pm
by MichaelK
Yes, the configuration is set.
Now you need to leveling your heatbed very precision! After leveling you could print.