G2S Pro Table will not travel lower than 6.3mm
Posted: Tue Feb 12, 2019 3:39 pm
I have no idea what is happening here.
I have the machine all calibrated. Every direction moves very accurately.
It doesn't matter what I do with any Z-value (in a program, in an offset, home offset, probe offset...) the machine will not get any closer than 6.3mm from the table! This is the display showing me this (which is what I can measure, too. Not like it reads one thing and is actually somewhere else)
Rather useless now...
Current settings:
I have the machine all calibrated. Every direction moves very accurately.
It doesn't matter what I do with any Z-value (in a program, in an offset, home offset, probe offset...) the machine will not get any closer than 6.3mm from the table! This is the display showing me this (which is what I can measure, too. Not like it reads one thing and is actually somewhere else)
Rather useless now...
Current settings:
Code: Select all
02:38:19.863 : echo:SD init fail
02:38:19.925 : echo:Active Extruder: 0
02:38:19.925 : FIRMWARE_NAME:V1.0.04 FIRMWARE_URL:http://firmware.ultimaker.com PROTOCOL_VERSION:1.0 MACHINE_TYPE:G2Spro EXTRUDER_COUNT:2 UUID:00000000-0000-0000-0000-000000000000
02:38:19.925 : X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 0.00 Y:0.00 Z:0.00
02:38:19.925 : echo:Active Extruder: 0
02:38:19.925 : Begin file list
02:38:19.925 : End file list
02:38:19.941 : echo:Active Extruder: 0
02:39:56.366 : echo:Steps per unit:
02:39:56.428 : echo: M92 X79.50 Y79.50 Z79.50 E48.13
02:39:56.428 : echo:Maximum feedrates (mm/s):
02:39:56.428 : echo: M203 X1000.00 Y1000.00 Z1000.00 E100.00
02:39:56.428 : echo:Maximum Acceleration (mm/s2):
02:39:56.428 : echo: M201 X5000 Y5000 Z5000 E5000
02:39:56.428 : echo:Accelerations: P=printing, R=retract and T=travel
02:39:56.428 : echo: M204 P1000.00 R2000.00 T2000.00
02:39:56.428 : echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
02:39:56.428 : echo: M205 S0.00 T0.00 B20000 X20.00 Z20.00 E5.00
02:39:56.428 : echo:Home offset (mm):
02:39:56.428 : echo: M206 X0.00 Y0.00 Z8.30
02:39:56.428 : echo:Endstop adjustment (mm):
02:39:56.428 : echo: M666 X0.00 Y0.00 Z0.00
02:39:56.428 : echo:Delta settings: L=delta_diagonal_rod, R=delta_radius, S=delta_segments_per_second
02:39:56.428 : echo: M665 L197.50 R92.00 S200.00
02:39:56.428 : echo:Material heatup parameters:
02:39:56.428 : echo: M145 M0 H190 B55 F255
02:39:56.428 : echo: M145 M1 H230 B70 F255
02:39:56.428 : echo:PID settings:
02:39:56.428 : echo: M301 P22.20 I1.08 D114.00 C1.00
02:39:56.428 : echo:Filament settings: Disabled
02:39:56.428 : echo:Z-Probe Offset (mm):
02:39:56.428 : echo: M851 Z-3.50