Hi,
Can someone tell me a set [firmware XXX, arduino YYY, leveler installation manual] or [already functional firmware XXX, arduino YYY] that he would have tested on his own I3 Pro B printer and would allow self-leveling on my I3 pro B equipped with a 3D touch levelling sensor ?
Thank you in advance.
Michael
Auto-levelling
Re: Auto-levelling
Hello, you can refer to the link below:
http://www.geeetech.com/Documents/3DTou ... Manual.pdf
http://www.geeetech.com/Documents/3DTou ... Manual.pdf
Re: Auto-levelling
Thanck you.
However, it lacks the version of the arduino programmer which allows the compilation of the firmware that you indicate. You need 1.0.8 or 1.0.6 (I tested both). The 1.8.5 I was using does not allow this.
Now I am trying to center the printing nozzle on my printing plate. In other words, when I print an object centered in the mark displayed in repetier, I would like it to be centered on my plate as well.
Where to settle this?
- in the printer settings in repetier host?
- in the slicer settings?
- in the EEPROM settings?
Why not group all these explanations (self-leveling, nozzle centering etc.) in the printer folder on your site? We waste so much time looking for them, finding the right ones, trying !!!
However, it lacks the version of the arduino programmer which allows the compilation of the firmware that you indicate. You need 1.0.8 or 1.0.6 (I tested both). The 1.8.5 I was using does not allow this.
Now I am trying to center the printing nozzle on my printing plate. In other words, when I print an object centered in the mark displayed in repetier, I would like it to be centered on my plate as well.
Where to settle this?
- in the printer settings in repetier host?
- in the slicer settings?
- in the EEPROM settings?
Why not group all these explanations (self-leveling, nozzle centering etc.) in the printer folder on your site? We waste so much time looking for them, finding the right ones, trying !!!
-
jackyjoy123
- Posts: 4
- Joined: Fri Jan 01, 2021 6:29 pm
Re: Auto-levelling
Hi buddy, first mail the geeetech team your need, they will definitely not say on. Give a try!prof2020 wrote: ↑Wed Apr 28, 2021 7:46 pmThanck you.
However, it lacks the version of the arduino programmer which allows the compilation of the firmware that you indicate. You need 1.0.8 or 1.0.6 (I tested both). The 1.8.5 I was using does not allow this.
https://creditcardsupportx.com/burlington-credit-card
https://creditcardsupportx.com/zulily-credit-card
https://creditcardsupportx.com/american ... redit-card
Now I am trying to center the printing nozzle on my printing plate. In other words, when I print an object centered in the mark displayed in repetier, I would like it to be centered on my plate as well.
Where to settle this?
- in the printer settings in repetier host?
- in the slicer settings?
- in the EEPROM settings?
Why not group all these explanations (self-leveling, nozzle centering etc.) in the printer folder on your site? We waste so much time looking for them, finding the right ones, trying !!!
thanks alot.
Last edited by jackyjoy123 on Mon Aug 23, 2021 11:13 pm, edited 1 time in total.
Re: Auto-levelling
[/quote]
Hi buddy, first mail the geeetech team your need, they will definitely not say on. Give a try!
thanks alot.
[/quote]
I gave it a try and auto-levelling seems to work.
Now I'm trying to center the printing nozzle on my printing plate.
Files admin gave doesn't seem to show how to do this.
Regards,
Michael
Hi buddy, first mail the geeetech team your need, they will definitely not say on. Give a try!
thanks alot.
[/quote]
I gave it a try and auto-levelling seems to work.
Now I'm trying to center the printing nozzle on my printing plate.
Files admin gave doesn't seem to show how to do this.
Regards,
Michael