Page 1 of 2
TMC2208
Posted: Fri Nov 02, 2018 6:00 am
by snir2001
Hi guys,
I have a problem with my A30 and maybe you will have the answer...
I just changed the drivers to TMC2208 and this sh!*t is briliant !!! but, somehow I can't make it work on the X...
Y,Z and E working great, but the X don't want to lock or move.
When I home the X, it's working, but refuse to move from there.
I tried Vref, and changing to another TMC2208 but nothing.
Back to the A4988 and the X is live again.
Any ideas????
BTW, the board is Gtm32 pro vd
Re: TMC2208
Posted: Sat Nov 03, 2018 6:59 am
by Lexan
GTM32 Pro ? Normally the A30 have the mini, anyway look here
https://www.geeetech.com/forum/viewtopi ... 92&t=61761
Re: TMC2208
Posted: Mon Nov 05, 2018 1:19 am
by snir2001
Yes, I got it with the Pro.
I already removed the bridge and update firmware, but it's the same problem
Re: TMC2208
Posted: Wed Nov 07, 2018 8:28 pm
by William
Hey
Could you tell us your fw version?
You need to tell us your PSU type also(12V or 24V).
Re: TMC2208
Posted: Sat Nov 10, 2018 1:59 am
by snir2001
Hardware version 3.2 24v
Latest firmware.
Re: TMC2208
Posted: Tue Nov 13, 2018 9:30 am
by William
snir2001 wrote: ↑Sat Nov 10, 2018 1:59 am
Hardware version 3.2 24v
Latest firmware.
The latest firmware version is:V1.37.58.You need to update it to this firmware version then test it.
Re: TMC2208
Posted: Sat Nov 17, 2018 4:35 am
by goranobradovic
I have the same problem. HW version 2.1, 24V PSU.
When I upgrade to FW 57 or 58, X works until I execute G28, or G28 X. After homing - X axis is dead.
On 56 it seems to be working (with TMC2208 drivers) but I am worried as the linked thread says I need to have newer firmware.
I measured voltage on X axis driver while homing - there are no drops or changes, it is same after homing but stepper won't move anymore.
Re: TMC2208
Posted: Sat Nov 17, 2018 5:20 am
by goranobradovic
Actually after some printing, issue happens in V56 too. For now I will just remove G28 and manually make sure that axes are homed before every print. I will upgrade again to 58. If you need me to test anything (test builds), you can contact me (I am also in group on FB, you can message me).
Re: TMC2208
Posted: Tue Nov 27, 2018 9:36 am
by William
goranobradovic wrote: ↑Sat Nov 17, 2018 4:35 am
I have the same problem. HW version 2.1, 24V PSU.
When I upgrade to FW 57 or 58, X works until I execute G28, or G28 X. After homing - X axis is dead.
On 56 it seems to be working (with TMC2208 drivers) but I am worried as the linked thread says I need to have newer firmware.
I measured voltage on X axis driver while homing - there are no drops or changes, it is same after homing but stepper won't move anymore.
Thanks for your feedback,we will check it'
Re: TMC2208
Posted: Wed Nov 28, 2018 6:25 pm
by Lexan
Hardware Version 3.2 have the GT32 Por Bord and need a modified Firmware version for TMC's