E180 Under Extruding?

[VooPoc]

Hi Guys,

FYI I'm new to 3d Printing.

I was looking at calibration to improve prints on my E180 and I've done a 100mm extrusion test and it's short my 31mm so its only extruding 69mm.

Some of the tutorials I have watched use code M501 to show parameters, which doesn't work. Does anyone know how I can calibrate the E180?

Thanks,

[William]

Maybe you should properly increase the A4988 driver board voltage(Normal is 0.8-1.1V)

A4988-B.png (635.33 KiB) Viewed 11935 times

If you use cura for slicing, you can increase the filament flow in the setting

[VooPoc]

Thank for this, I will look into it and check the voltage. Is there any means to do this via firmware and gcode gets and sets (or whatever they are called in this language).

[William]

I think you can try to print a 20MM cube, and then see the size is normal, in order to determine whether the normal extrusion

[VooPoc]

Hi Willam,

Is it possible to ask your admins to install a plugin such as "image upload" on your phpBB deployment?

I cracked open the bottom and noticed the Z_A1, Y_A1, X_A1 clustered together. The E2_A1 is separate and I assume needs tweaking. I am disappointed that this isn't a function via firmware or even Gcode.

Before I play around with any of these physical settings can you confirm there are no other means of calibration?

Thanks,

[William]

You can upload the pic to Google drive,I will check it at first.

[VooPoc]

Hi William,

The stock voltage I have on the E2_A1 was 0.46v and when I increased the voltage it made no difference to the extrusion length, it does appear to have increased the speed, but not the steps/mm. Additionally, when I increased the voltage to 0.93v the motor started to make a tick sound and jitter.
Therefore, reduced it back to 0.46v.

Any ideas?

Thanks,

[William]

I use "SSCOM 4.2" and send "M2002 E * \ R \ N" to change steps per mm

[VooPoc]

I think you might need to provide a little more info?

I have done a search on SScom and it appears to be a debugger tool. I have however executed M2002 using pronterface and it outputs what I'm looking for. Is there any documentation on using M2002? I want to know what I'm executing and "E * \ R \ N" isn't self-explanatory.

Thanks,

Output:
>>> M2002
SENDING:M2002
min_position[X_AXIS]:0.00;min_position[Y_AXIS]:0.00;min_position[Z_AXIS]:0.00;max_position[X_AXIS]:130.00;max_position[Y_AXIS]:130.00;max_position[Z_AXIS]:132.00;steps_per_mm[X_AXIS]:80.000000;steps_per_mm[Y_AXIS]:80.000000;steps_per_mm[Z_AXIS]:400.000000;steps_per_mm[E_AXIS]:70.000000;max_feedrate[X_AXIS]:550;max_feedrate[Y_AXIS]:550;max_feedrate[Z_AXIS]:35;max_feedrate[E_AXIS]:50;home_speed[X_AXIS]:300;home_speed[Y_AXIS]:300;home_speed[Z_AXIS]:120;home_position[X_AXIS]:0;home_position[Y_AXIS]:1;home_position[Z_AXIS]:1;motor_direction[X_AXIS]:0;motor_direction[Y_AXIS]:1;motor_direction[Z_AXIS]:1;motor_direction[E_AXIS]:1;motor_direction[E1_AXIS]:0;motor_direction[E2_AXIS]:1;motor_direction[X_AXIS]:0;motor_direction[Y_AXIS]:1;motor_direction[Z_AXIS]:1;motor_direction[E_AXIS]:1;motor_direction[E1_AXIS]:0;motor_direction[E2_AXIS]:1;motor_direction[X_AXIS]:0;motor_direction[Y_AXIS]:1;motor_direction[Z_AXIS]:1;motor_direction[E_AXIS]:1;motor_direction[E1_AXIS]:0;motor_direction[E2_AXIS]:1;HV:V1.4;
ok

[William]

Default steps per mm of extruder value is 65 (E65)