Require full Prusa I3 Aluminium Kit Assembly Instructions

zhangxueyou · Post by **zhangxueyou** » Fri Feb 13, 2015 10:01 am

Wiring of power supply cable

: Wiring of power supply cable.png (281.58 KiB) Viewed 31337 times

: Wiring of power supply cable2.png (373.01 KiB) Viewed 31337 times

: Wiring of power supply cable3.png (691.46 KiB) Viewed 31337 times

zhangxueyou · Post by **zhangxueyou** » Fri Feb 13, 2015 10:04 am

Z motor (2 in all)

: Z motor(2 in all).png (535.02 KiB) Viewed 31337 times

: Z motor(2 in all)2.png (435.72 KiB) Viewed 31337 times

: Wiring of Z motor.png (515.74 KiB) Viewed 31337 times

Post by **Admin** » Fri Feb 13, 2015 10:49 am

Wiring of Z motor

: Wiring of Z motor3.png (422.18 KiB) Viewed 31336 times

: Wiring of Z motor2.png (426.99 KiB) Viewed 31336 times

: Wiring of Z motor4.png (792.78 KiB) Viewed 31336 times

The pictures above are all the wiring of each part. Hope it will help you successfully complete it.

Anabatix · Post by **Anabatix** » Tue Feb 17, 2015 7:36 am

Thank you this has been a big improvement.
Did you also send the replacement LCD as promised?
http://www.geeetech.com/reprap-ramps-v1 ... p-615.html
It is the only thing missing from finishing my project.

I did notice some small errors in your wiring perhaps.
1. The Z axis can not be wired like that unless you supply in your kit 2 extra wires. The plugs on Z axis board would not fit without thinner plug adaptor.
2. End stop wiring is different to RepRap project pin positions. So I will try Reprap wiring diagram first. And it depends on if they are for minimum or maximum end stop position.What are your thoughts?

Reference http://reprap.org/wiki/Prusa_i3_Rework_ ... ors_wiring

Kind regards

Lee

Post by **Admin** » Tue Feb 17, 2015 8:38 am

1. There is no enough zone to plug Z motor directly. So we add Dupont wire, can you see that in the picture?
2. I am so sorry for this, because I am new guy. I need time to know these things step by step. So please forgive my fault. And thank you for your tips.
Good luck!

Anabatix · Post by **Anabatix** » Tue Feb 17, 2015 8:51 am

Hi,

Yes the photos were a good help. The Dupont wire was not in the kit so I had to order some from a local supplier.
Did anyone send the missing LCD controller? Can you check for me please.

Thank you for all your help.
My printer is looking very good now.

Regards Lee

Post by **Admin** » Tue Feb 17, 2015 8:57 am

We have sent the missing LCD to you last week. It takes about 5-10 days. Please be wait patiently.

Anabatix · Post by **Anabatix** » Tue Feb 17, 2015 9:02 am

Excellent.
Have a great day!

Post by **Admin** » Tue Feb 17, 2015 9:06 am

Good luck!

Anabatix · Post by **Anabatix** » Tue Feb 17, 2015 10:52 am

I just check my mailbox and the LCD parts are sitting there waiting for me!
That was super fast, many thanks.

Lee

Geeetech

Require full Prusa I3 Aluminium Kit Assembly Instructions

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction