Geeetech

Hi Folks<
I am new to 3d printing but have lots of NC and CNC experience.

I have a second hand i3 printer and am running Repetier v1.6.2

I have succeeded in printing one job (a few weeks ago).

I now am stuck with the printer going start to "Print Job Paused" when ever I try to print anything.

The job appears correctly in the Print Preview window.

In the print log it appears to executing commands from a completely different program. My program has 42 lines but the log seems to be executing line below???

The printer works OK under manual control - Homes OK and is not stuck on a limit switch.

Any ideas gratefully received.

10:49:22.050 : N882 M117 ETE 1m 12s*126
10:49:23.690 : N883 M105*36
10:49:26.753 : N884 M105*35
10:49:27.081 : N885 M117 ETE 1m 12s*121
10:49:29.815 : N886 M105*33
10:49:32.112 : N887 M117 ETE 1m 12s*123
10:49:32.878 : N888 M105*47
10:49:35.940 : N889 M105*46
10:49:37.144 : N890 M117 ETE 1m 12s*125
10:49:39.003 : N891 M105*39
10:49:42.066 : N892 M105*36
10:49:42.175 : N893 M117 ETE 1m 12s*126
10:49:45.128 : N894 M105*34
10:49:47.206 : N895 M117 ETE 1m 12s*120
10:49:48.191 : N896 M105*32
10:49:51.253 : N897 M105*33
10:49:52.238 : N898 M117 ETE 1m 12s*117
10:49:54.316 : N899 M105*47
10:49:57.269 : N900 M117 ETE 1m 12s*117
10:49:57.378 : N901 M105*47
10:50:00.441 : N902 M105*44
10:50:02.300 : N903 M117 ETE 1m 12s*118
10:50:03.503 : N904 M105*42
10:50:06.566 : N905 M105*43
10:50:07.331 : N906 M117 ETE 1m 12s*115
10:50:09.623 : N907 M105*41
10:50:12.357 : N908 M117 ETE 1m 12s*125
10:50:12.686 : N909 M105*39
10:50:15.748 : N910 M105*47
10:50:17.389 : N911 M117 ETE 1m 12s*117
10:50:18.811 : N912 M105*45
10:50:21.873 : N913 M105*44
10:50:22.420 : N914 M117 ETE 1m 12s*112
10:50:24.936 : N915 M105*42
10:50:27.451 : N916 M117 ETE 1m 12s*114
10:50:27.998 : N917 M105*40
10:50:31.061 : N918 M105*39
10:50:32.483 : N919 M117 ETE 1m 12s*125
10:50:34.123 : N920 M105*44
10:50:37.186 : N921 M105*45
10:50:37.514 : N922 M117 ETE 1m 12s*117
10:50:40.248 : N923 M105*47
10:50:42.545 : N924 M117 ETE 1m 12s*115
10:50:43.311 : N925 M105*41
10:50:46.374 : N926 M105*42
10:50:47.577 : N927 M117 ETE 1m 12s*112
10:50:49.436 : N928 M105*36

Hi， Can you provide a specific video or picture?
Are you printing via sd card or printing via USB?
The feedback temperature displayed by the information you provide，

Hello.


I can offer you to install the current version of Repetier-Host.
Gcode M117 is a command that updates the information presented on the LCD display of the printer.
M105 is responsible for temperature readings from the printer. So this is definitely your Gcode.

These are operations carried out automatically by Repetier-Host.

Of course, when you delve into the configuration of the program you can modify or disable it. It's important that you know what you're doing.

It is a pity that you did not attach your print file (Gcode).
In such a situation I can recommend that you familiarize yourself with the topics on the forums with a similar problem.
You can also read this.