GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post Reply
aubin80
Posts: 8
Joined: Mon Mar 30, 2015 6:54 am

GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by aubin80 » Mon Mar 30, 2015 7:00 am

Hello Everybody,

Trying to fix the X Motor direction, I did something bad.
Now my printer is not working because of the bad firmware.

It would be pleasant if anyone could send me the firmware for the next config:
- PRUSA I3 with RAMPS 1.4
- LCD 2004 Controller
- MK2A with 100k NTC Thermistor

Thank you,

Aubin
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by zhangxueyou » Wed Apr 22, 2015 4:16 pm

Do you have email? I can send you the firmware.
Top
aubin80
Posts: 8
Joined: Mon Mar 30, 2015 6:54 am

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by aubin80 » Sun Apr 26, 2015 10:56 pm

I finally find a virgin firmware (marlin) and I made it working for the geeetech prusa i3.
It would be nice from you to send me the firmware to compare and change some details on my firmware.
In fact I have some problems with the temperature regulation when heating the noozle.

My email adress is adef-80@live.fr

Thank you very much for your time.

Aubin
Top
Endymian
Posts: 1
Joined: Fri May 08, 2015 8:34 am

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by Endymian » Fri May 08, 2015 8:38 am

zhangxueyou, I believe I also require the exact same firmware files.
I have an i3 pro with the LCD 2004 controller and a RAMPS 1.4. The vendor we purchased the unit from on Amazon sent us the firmware for the board this unit was apparently supposed to come with, but substituted with this RAMPS 1.4.

my email address is : ssj5jemak @ gmail . com
Top
vortex4200
Posts: 2
Joined: Sun Jun 07, 2015 8:18 am

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by vortex4200 » Sun Jun 07, 2015 8:20 am

I too am looking for the firmware for my RAMPS 1.4, could I have a copy of what you are using?
mike3d@hotmail.com
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by zhangxueyou » Mon Jun 08, 2015 9:14 am

vortex4200 wrote:I too am looking for the firmware for my RAMPS 1.4, could I have a copy of what you are using?
mike3d@hotmail.com
Hi, we'd sent the firmware to your email for twice but failed. So we sent it to your register email, please check.
Top
vortex4200
Posts: 2
Joined: Sun Jun 07, 2015 8:18 am

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by vortex4200 » Mon Jun 08, 2015 6:15 pm

oh sorry I left something out of my email address lets try that again! :D
it's mikelang3d@hotmail.com sorry about the mix up.

Mike
Top
Jacques
Posts: 5
Joined: Sat Mar 21, 2015 4:04 am

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by Jacques » Thu Jun 18, 2015 3:58 am

Hi there,

Can you please mail me the firmware as well for the Geeetech I3 B, 2560, Ramps 1.4

JacquesW@JTDental.co.za
Top
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by zhangxueyou » Thu Jun 18, 2015 9:46 am

Jacques wrote:Hi there,

Can you please mail me the firmware as well for the Geeetech I3 B, 2560, Ramps 1.4

JacquesW@JTDental.co.za
Sorry, but the email we sent you was rejected for some unknown reason, could you please leave other email address?
Top
Jacques
Posts: 5
Joined: Sat Mar 21, 2015 4:04 am

Re: GEETECH PRUSA I3 RAMPS 1.4 FIRMWARE CRASHED

Post by Jacques » Thu Jun 18, 2015 11:56 am

Hi there.

You can try c13pt01@gmail.com
Top
Post Reply

Return to “Firmware”