Search found 14 matches

by OleOhlsen
Mon Nov 18, 2019 6:37 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

No, it didn't work with the old version. I will try another card, I have one in my camera.
If the card slot would be defect it should not show Media at start screen.
by OleOhlsen
Mon Nov 18, 2019 5:43 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

I already doing a test print, and so far it is finished it looks MUCH better than before!!! Thank you for sharing the firmware! Only one issue is left: It does not accept my SD card. I already tried all advises I found at the web, but no success. I tried format on my mac, at my Canon camera (like so...
by OleOhlsen
Mon Nov 18, 2019 12:51 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

Yeahhh, I (you, we) got it! Display shows what it should!!!
Thank you so much!!!! :D

Now I have to configure all. Hope I will find some information....
by OleOhlsen
Sun Nov 17, 2019 8:50 pm
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

Thank you for your nice patience with me! I didn't know much about 3D printing before I bought the printer. I looked for tests at the web, and this was recommended as a good price-performance ratio, so I ordered it. To mount the set cost me 4 hours (youtube videos, no paper instruction was with the ...
by OleOhlsen
Sun Nov 17, 2019 5:03 pm
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

Ok, thank you!
I was able to do a setup (more a try and error than knowhow, because I don't know specifics like FMP or TMC2208) with no error, but display is still the same!?
Where can I learn what parts i have, and which drivers I need?
by OleOhlsen
Sun Nov 17, 2019 7:30 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

I don't know the basics, how to enable/ disable...

Ok, I'll check tomorrow morning! It's after midnight over here and I'm tired..
Thank you for your help, much appreciated!
by OleOhlsen
Sun Nov 17, 2019 7:11 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

This looks quite difficult! Is'nt there a outofthebox solution?
by OleOhlsen
Sun Nov 17, 2019 6:54 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

Sorry, I'm absolute new with 3D printing...
I used Arduino, selected 2560 board and /dev/cu.usbserial-1460
Thats all, then checked and uploaded. Is there anything else to do?
by OleOhlsen
Sun Nov 17, 2019 6:43 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

Like you suggested Marlin-bugfix-2.0.x-B422
by OleOhlsen
Sun Nov 17, 2019 6:39 am
Forum: Geeetech I3 Pro B
Topic: Firmware update failed, display shows rectangle only!
Replies: 13
Views: 10534

Re: Firmware update failed, display shows rectangle only!

I checked the cable, but they are all in place! No change when I wiggle it.... :(